• Sonuç bulunamadı

臺北醫學大學100學年度碩士班暨碩士在職專班招生入學考試_齒顎矯正學組_齒顎矯正學試題

N/A
N/A
Protected

Academic year: 2021

Share "臺北醫學大學100學年度碩士班暨碩士在職專班招生入學考試_齒顎矯正學組_齒顎矯正學試題"

Copied!
1
0
0

Yükleniyor.... (view fulltext now)

Tam metin

(1)

新聞稿

臺北醫學大學

100 學年度碩士班暨碩士在職專班招生入學考試

齒顎矯正學試題 本試題第1頁;共1頁 (如有缺頁或毀損,應立即請監試人員補發) 注 意 事 項 一、本試題共七大題,共計100 分。 二、請將正確答案依題次作答於答案用卷內。 三、試題答錯者不倒扣;題次號碼錯誤或不按順序或鉛筆作答,不予計分。

1. Comparison between adolescents and adults in the biologic considerations in selection of a Orthodontic Treatment Plan. (10%)

2. Please describe the Scammon’s curve for growth of the four major tissue systems of the body. (10%) 3. Please describe the guidelines for orthodontic extraction. (10%)

4. Please list and compare the orthodontic arch wire materials. (10%) 5. A 10 years old girl with the cephalometric data : SNA= 850

,SNB= 790

,U1 to NA = 8 mm,L1 to NB=5 mm,IMPA=920

, FMA= 250

,what is your diagnosis and treatment plan for this patient?(10%)

6. 針對前牙齒列完全深咬(deep bite)(垂直覆蓋超過 100%)及開咬(open bite)(垂直覆蓋小於 0%)之咬合異常病例,請回 答下列問題: (1) 請分別敘述上述兩種咬合異常病例之顱顏牙齒形態特徵(craniofaciadental morphology),並製表比較兩種特徵之 相異處。(10%) (2) 請分別提出上述兩種咬合異常病例之原因(etiology)。(10%) (3) 請分別提出上述兩種咬合異常病例之齒顎矯正治療方式。(10%) 7. 依齒顎矯正學的觀點,有關微笑美學(esthetic smile),請回答下列問題: (1) 就牙齒與牙齦的關係,請說明影響微笑的因素?(10%) (2) 在齒顎矯正過程中,哪些治療機轉可以建立平衡微笑下的齒顎關係?(10%)

Referanslar

Benzer Belgeler

Soils with the highest organic matter content had the lowest degradation rate, indicating a tighter sorption of trifluralin.. This was not surprising since other researchers have

接種疫苗後應於接種單位或附近稍作歇息,並觀察至少30分鐘以上,待無不適後再離開;接種後應注意有無持續發燒(超過48小時)、意識或行為改變、呼吸困難、

Dil bilgisi konuları ile öğrencilerin ilgi ve ihtiyaçları arasında bir iliĢki olduğunda öğrenciler, kendi ilgi ve ihtiyaçlarına cevap veren çalıĢmalarla dil bilgisi

[r]

Araştırmada alt beden kalça postür problemlerinin özelliklerine göre tespit edilen 2 kişinin postür testi, vücut analiz formu ile vücut yapıları incelenmiş, biçki ve

PhD Mehdi Keshavarz Ghorabaee, Department of Industrial Management Allameh Tabataba’i University (ATU), Iran PhD Komeil Nasouri, Textile Engineering Department, Isfahan University